RAM-HOL-ZE25PHLU - RAM Mounts Form-Fit Holder (with Key Lock) for Zebra ET60/65

RAM-HOL-ZE25PHLU This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up

RAM-HOL-ZE25PHLU This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position. cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp, Temp-Right, NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 12VInput Cable Length: approx. 100 cmCertifications: RoHS, IC, FCC, WEEE, CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied. RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65RAM Mounts Cradles Mounting solutions RAM MOUNT

Key features

• RAM-HOL-ZE25PHLU This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up
• allowing them to operate in wet and freezing environments.To insert the device
• place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments
• while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PHLU:Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp
• Temp-Right
• NFC-Repeater or Zebra CAC ReaderHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 12VInput Cable Length: approx. 100 cm Certifications: RoHS
• IC
• FCC
• WEEE
• CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE25PHLU holder is supplied. RAM Mounts Form-Fit Holder (Key-Locking) for Zebra ET60/65RAM Mounts Cradles Mounting solutions RAM MOUNT